Step-by-Step Guide to Installing Your Emberglow Vented Topside Gas Log Set

Congratulations on purchasing the Emberglow gas log set, known for its realistic appearance and efficiency. This guide will walk you through the installation process, ensuring you enjoy the warmth and ambiance of a gas log fire without the hassle of traditional wood burning.

Overview of the Installation Process

The installation of your gas log set should take no more than an hour. Before you begin, it is crucial to read the owner's manual thoroughly, as this video serves only as a supplementary guide. If you prefer professional installation, consider contacting a licensed gas company, propane supplier, or plumber.

Pre-Installation Checks

Verify Gas Type and Size

Ensure that the log set you purchased matches the type of gas you will be using, either propane or natural gas. Additionally, confirm that you have the correct size of gas logs for your fireplace. Clearance requirements are provided on the box and in the owner's manual.

Safety Precautions

Since you have purchased a vented gas log set, it is essential to keep your chimney flue open during operation. To ensure safe operation, perform a draft check:

1. Open the flue completely.
2. Ignite a long stem of newspaper in the middle of your firebox.
3. Observe the smoke; it should rise into the chimney. If it flutters in the firebox, there is a drafting problem. In this case, postpone installation and contact a qualified service person.

Unpacking the Log Set

Once your chimney passes the draft check, unpack the log set. Depending on whether you have a Radco or AGA certified log set, you will find different components:

• Radco Certified Set: Logs, aluminum tube, 3/8 inch flared elbow, supply fitting, damper clamp, grate, decorative stone, glowing embers, pipe dope, triple burner, burner pan, lock nut, grate enhancer, spacer, control knob, extension, and grate standoffs.
• AGA Certified Set: Includes all Radco components plus a valve, regulator, short nipple, thermal couple, heat shield, bracket with fasteners, and various elbows.

Tools Required

You will need the following tools for installation:

• Adjustable wrench
• Pipe wrench
• Hammer
• Screwdriver

Preparing the Fireplace

If your fireplace has previously burned wood or coal, it is recommended to clean both the firebox and chimney before installation. Additionally, install the damper clamp on the chimney damper to prevent accidental carbon monoxide buildup by keeping the chimney flue from closing completely.

Assembly Instructions

Determine Assembly Side

Check which side of the firebox your gas line is on to prepare for right or left-hand assembly.

Burner Pan Assembly

1. Remove the knockout hole from the right side of the burner pan.
2. Slide the burner support spacer onto the burner bar and place the burner bar into the pan.
3. Attach the lock nut to the unflared end of the 3/8 inch brass fitting and apply pipe dope.
4. Place the fitting through the open knockout hole and secure it to the internal threads of the burner bar. Tighten the lock nut until it rests securely against the pan.

Installing the Safety Pilot Kit (if applicable)

If using a safety pilot kit, fasten the pilot bracket to the burner pan using self-tapping screws. Apply pipe dope to each fitting during assembly to prevent gas leaks.

1. Fasten the straight flared fitting into the end port of the regulator.
2. Attach the short nipple to the outport of the regulator and then to the back of the valve, tightening all fittings with a wrench.
3. If purchased separately, fasten the straight fitting directly to the back of the valve and connect the thermal couple and thermal cutting leads.

Connecting the Gas Supply

1. Secure the supply line with a pipe wrench, ensuring the fitting is firmly attached without putting torque on the supply line.
2. Carefully bend the aluminum tubing as needed to reach the supply line, avoiding kinks.
3. Attach the aluminum tube to the unit and the supply line, tightening snugly.

Filling the Burner Pan

Pour granules into the burner pan until full, ensuring they are evenly sloped.

Leak Testing

To check for leaks, create a 50/50 solution of liquid soap and water. Ignite the burner by slowly opening the valve while lighting a long ignition device next to the burner.

1. Sponge soapy water on all connections; if bubbles appear, turn off the gas valve, tighten connections, and repeat the test until no leaks are detected.

Log Placement

1. Place half of the glowing embers over the burner bar, hiding the gas inlet if desired.
2. Attach the grate enhancer to the grate assembly.
3. Position the back log (shorter log) securely on the log standoffs, followed by the front log (longer log) as far forward as possible for optimal combustion.
4. Arrange the smaller top logs according to the owner's manual.
5. Cover the top burner with the remaining glowing embers.

Ignition and Operation

To ignite your set with a safety pilot kit:

1. Turn the valve to the pilot position while holding an ignition device to the pilot assembly.
2. Push the control knob in; it may take a minute to bleed the air out of the gas line.
3. Once the pilot is lit, continue pressing the control knob for 20 to 30 seconds to stabilize the pilot.
4. Turn the control knob to the on position.

Burnoff Period

Your log set will have a burnoff period of 2 to 3 hours, during which colorants used in manufacturing may emit an odor. This will diminish with continued use.

Conclusion

If you have any additional questions or concerns regarding your gas log set, refer to your owner's manual or call the customer service hotline at 1-800-229-5647. Thank you for choosing the Emberglow gas log heater; we are confident it will provide you with high efficiency and realistic beauty for many years to come.